Drone 2.0 Mainboard and Navigation Board Replacement Mainboard and Navigation Board Help make this guide better by using the correct tools in images and/or text. Use this guide to replace the mainboard and navigation board in your Parrot AR.Drone 2.0 spare parts and mounting tools are available from several Parrot retailers. Remove the foam body. Disconnect the battery by pulling the two red wires apart. Remove the battery by releasing the battery retaining straps. Turn the drone upside down. The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover. Using a spudger, separate the connector for the downward camera. Remove the camera from the body by pulling it off the foam body. Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors. Use tweezers to carefully remove the ribbon from the connector. Remove the four 8mm torx screws with a T6 bit.

Remove the four 8mm philips head screws with a PH00 bit. Carefully pull the secondary board from the mainboard. Turn the drone right side up Remove the USB connector from the battery retaining straps. Release the rubber clip holding the USB and battery power cable to the body.buy a drone in canada Avoid using sharp tools near the battery.parrot ar drone firmware upgrade Push the USB and power cable through the battery panel.buy ar drone online Turn the drone upside down again. Use a spudger to release the connector and carefully remove the ribbon. Lift the mainboard up so that you can access the back. Disconnect the first connector with the white wires using a nylon spudger. Disconnect the second connector with the red and black wires using a spudger.

The mainboard is now fully detached and can be removed. To reassemble your device, follow these instructions in reverse order. Past 24 Hours: 3 Past 7 Days: 26 Past 30 Days: 96 Used & new (2) from $77.70 + $4.99 shipping Selection for all your crafting needs, from jewelery making products and art supplies to gift wrapping and more. Drone Replacement Navigation Board Parrot AR Drone 2.0 Navigation board Parrot AR Drone 2.0 Main Board See more technical details The navigation board includes the sensors and a 40 MIPS microcontroller with a fast 12 bits ADC converter. The navigation board has one ultrasonic transceiver and one ultrasonic receiver to measure the height of the drone up to 6 meters / 20 feet. The altimeter provides a measure at a 25 Hz rate. A 3 axis digital MEMS accelerometer positioned at the center of gravity of the AR.The accelerometer is used in a +/- 2g range and digitalized by an on-chip 10 bit ADC. Data are sent to the microcontroller.

A two axis MEMS gyroscope and a precision piezoelectric gyroscope for the yaw measurement and heading control. Both sensors measure up to 500 °/s. These are analog sensors digitalize by the 12bits ADC of the microcontroller. These sensors compose the inertial measurement unit. The fusion of these data allows computing the Euler angles of the AR.Euler angles are used for stabilization. The navigation board software may be updated when you update the AR.This kit includes 1 navigation board and 4 screws. 6.6 x 6.3 x 0.9 inches 5.0 out of 5 stars #461 in Arts, Crafts & Sewing > Craft Supplies > Paper & Paper Crafts > Papermaking 55 star100%See all verified purchase reviewsTop Customer ReviewsWorked for me...Prevented my son's drone from being junkedSo easy!!Five StarsFinally I can use de Ar.Drone Arts, Crafts & Sewing > Crafting > Paper & Paper Crafts > PapermakingPX4IOAR is an electrical and mechanical adapter board. Includes everything needed to put PX4FMU on a Parrot AR.

Drone 1.0 or 2.0.Drone is a trademark of Parrot SA, Paris. The PX4IOAR board is compatible to the AR.Drone 1.0 and 2.0 frame and motor controllers. PX4 is not affiliated to Parrot. PX4IOAR is not using any Parrot technology or software. Order this module from: UnmannedTech (UK & EU) BYOD (UK & EU) UAV store (Germany & EU) Step-by-step build instructions can be found on the AR.Drone Shield (PX4IOAR) page. The PX4IOAR is sold by 3D robotics with a complete mounting kit for the AR.Drone 1.0 and AR.Only battery power cable, battery, RC receiver and a short receiver cable (servo cable) need to be added. PX4IOAR v1.2 User Manual PX4IOAR v1.2 Schematic and Layout All documentation in hardware repository The following connectors can be used to make connections between PX4IOAR and other devices. Google Sketchup can be used to view and render the highly-detailed 3D model of PX4IOAR (SketchUp Pro can export to industry CAD software): PX4 Modules in the Google 3D Warehouse

PX4IOAR is designed with Cadsoft Eagle v 6.2. PX4IOAR v1.2 Eagle board (Eagle 6.2, current board version) PX4IOAR v1.2 Eagle schematic (Eagle 6.2, current board version) PX4IOARMT v1.0 Eagle board (Eagle 6.2, current board version) PX4IOARMT v1.0 Eagle schematic (Eagle 6.2, current board version) New (17) from $34.44DetailsParrot AR Drone 2.0 Main Board FREE Shipping. AR Drone 2.0 Navigation board 8.5 x 1.5 x 6 inches 4.0 out of 5 stars #22 in Industrial & Scientific > Robotics > Robot Parts & Accessories > Robot Accessories #27,973 in Computers & Accessories > Tablet Accessories #82,021 in Electronics > Accessories & Supplies > Cell Phone Accessories 5 star53%4 star16%3 star21%1 star10%See all verified purchase reviewsTop Customer ReviewsSo I said why not I enjoyed flying it|Works as promised|guess you can never have too many spare now boards|I bought this and I am back up in the sky having fun!|Just what I needed.|Drone 2.0 * GENUINE NAVIGATION BOARD * Transceiver and Receiver Gyro