Check all the props for damage and debris around the shafts(string and things like that). Other than that make sure you have a fully charged battery I had the same problem after switching my propellers out, my drone (X5SW) didn't want to lift and kept tilting to the right. After some searching I found that if you don't have the propellers in the right sequence, that you're not going anywhere. I switched the props to the picture on the box and low and behold, I'm flying again! If the motors are spinning up, it is likely an issue with the flight controller or ESC's. Have you tried calibrating the gyros? Turn the copter on and place on the level surface, I believe it is both sticks down and to the right (might be left, varies from manufacturer), hold and watch the LED's on the bottom flash, once the flashing stops it should be calibrated. I have seen that happen before after taking a crash. If the gyros don't agree with each other it won't fly. Do the motors actually respond to the throttle up to point?

Meaning you can spin them up and down a little bit just not enough to take off? Or is it just spinning in Idle when you turn it on? Also, I'm not sure if it was a question or just a comment, but you should always have 2 motors spinning clockwise, and 2 counter clockwise. On a lot of these toy grade drones if you get hung in a tree and the transmitter is still throttle up you are going to burn out something. parrot ar drone in south africaI had issues when I was new to the hobby, so I feel your pain.remote control drone brookstone Props are marked A and B. Make sure they're mounted on the correctly marked arm of the quad. parrot ar drone warranty Motors cost nothing a few pounds for a set of 4 . ar drone 2 pilotage

If u crashed it u more than likely damaged the motors or control board. Check all the solder points are ok and no wires are detached. If thats ok and the motors rev up and respond to transmitter power then the board is naf. U can bypass the power control by placing a small blob of solder on the board in the right place. parrot ar drone improvementsThis bypasses the gyros and enables normal flight again. parrot ar drone zaThe gyros perm set at default so no need for calibration. When your thing is spining but is not going up in the air what do you do . Posted: March 7, 2017 i have kk5.5 board...ive made xcopter....all the motors are rotating perfectly.... 2 motors in clockwise and 2 motors in counter clockwise direction but the problem is the drone is not lifiting off...can u say a solution for itttt....how to hover a quadcopterOn this page, I’ll be going over how to hover a quadcopter, or in other words, how to get the quadcopter off the ground for the first time without crashing.

Start off with about 10% throttle, then slowly move all your controls to make sure that everything is working properly before flight. Do not fly unless you know for sure that every control is working correctly.Get To Know Your Quadcopter. Slowly increase the throttle until the quadcopter is hovering at about 2 inches off the ground, then slowly move the controls around to get a feel for how fast the quadcopter reacts to your inputs. If you have a quadcopter with long landing gear, it’s better to fly at about one foot to avoid getting the landing gear caught on the ground. If you start to feel like you’re loosing control, quickly throttle down, then pick the quadcopter up and put it back to where you took off from.After you’ve gotten a good feel for the controls, raise the quadcopter to about 3 feet. Once it’s up there hovering, it should become slightly easier due to the lack of air turbulence coming from the ground.Set up a few targets to try landing on, then fly to each target, land, and fly to the next one.

This will really help with your hovering precision and landing ability.Start with the quadcopter at the 10 o’clock position, then hover there until you’re confident enough to move to the next position. After that, you can start doing positions 2, 9 and 3 (when I say “o’clock” I’m referring to the positions of the hands on a clock face).nose-in-hovering is a term used by RC helicopter pilots which basically just means that the nose of the helicopter (or in this case a quadcopter) is facing you. When practicing nose-in-hovering for the first time, you should manually pick the quadcopter up and turn it so it’s facing you, then take off. Once you’re off the ground, both your aileron and elevator controls will be backwards, so at first it won’t be easy to keep the quadcopter in one spot. I like to think of nose-in-hovering like balancing a stick. Which ever way the stick/quadcopter falls, that’s the way your hand/control-stick should be moving. Once you’re able to do nose-in-hovering, you can finish learning orientation by practicing hovering in the 7 and 5 o’clock positions.

Set up some targets and try to land on them exactly the same way as before, but this time with the nose of the quadcopter facing in. This step is extremely hard, so take your time. Believe it or not, hovering is one of the hardest things to learn when flying. Hovering is hard, especially nose-in-hovering, So don’t worry if it takes you 3 days, or even 3 months to learn. The point of flying is to have fun. When you fly, I recommend learning whatever you’re not good at first for about half of the flight, then do whatever you want for the other half. That way you won’t get too bored or frustrated. Watch my video Tags: SK450The guide will help you to get started with NodeCopter hacking in any All NodeCopter hacking is done using the Parrot AR Drone The AR Drone 1.0 may also be supported by some libraries, but most of the community uses 2.0 drones. We are not married to the Parrot drones, but so far we have not found any alternatives that offer competitive pricing, automatic hovering, global

distribution, easy repairs and are shipped fully assembled. In most countries the best place to buy a drone is your national version of won’t get a discount, but shipping is usually very fast and they often also carry the repair parts you may need. If Amazon is not a viable option for you, you should consider the manufacturers Shipping can be slow, but they can deliver all parts to almost any country in For those willing to go the extra mile for a good deal, we recommend Ebay orYou can often find used drones or drones with minor damage. Repairing the drones is easy, so unless the damage is much bigger than advertised, you should be able to save a decent amount of money. Last but not least, there are several brick and mortar retailers, you can find Before starting your drone for the first time, you may want to know about this: Make sure that you have Node.js installed. First off, you should get the FreeFlight app for your iOS

device if you don’t have it already. Now connect to the drone’s WiFi with your smartphone, start the FreeFlight app and make a test flight with it’s Piloting feature to learn how the drone behaves. It’s also a good time to check if the firmware of the drone is up to date. setup the drones for exact instructions. But controlling the drone with the phone is boring, let’s program it! the drone’s WiFi with your laptop and install the ar-drone module: Once you’ve done that, save this to a file:See how your drone takes of, rotates clockwise and even does a flip!Now you’re set, go ahead and get crazy! Per default, the drone will only fly very slowly and won’t fly higher than 3m. These limits can be lifted via the mobile app or a library that supports it. Here is an example for setting the limit to 100m using the Looks like the emergency mode is in effect. To easy ways to fix this: Normally, if you’re connected to your drone’s WiFi you don’t have connection to