In this video I show how to solder and install the mirumod on my Parrot AR.Drone (specifically version 1.0). I don't have the 2.0's so can't get into too much details about it so please check the latest documentation regarding the newer versions of the AR.Even though I'm demonstrating this mod on a AR.Drone 1.0, a lot of the information is still relevant to the newer models with regards to the programming and testing. Just make note of the necessary LLC (logic level converter) for the AR.Drone 2.0 or you'll FRY it!This is an update to a video I did back in 2010 which used a Yellow Jacket to talk via WiFi to the Parrot AR.The mirumod by miru allows you to use your Parrot AR.Drone with a regular RC radio transmitter (Spektrum DX6i / Turnigy 9x / etc). This is an improved mod that doesn't require WiFi and you don't need to use your iOS or Android device. It uses an Arduino Pro Mini and plugs directly into port under ARDrone. Unplugging it will return it to factory. Disclaimer: I'm not responsible for any damage to you or your device.

Please read all current documentation because the information could be out of date by the time you watch this video. /////products/11113AR.Drone 1.0 - 4.7k ohm resistor for TXO pin (AR.ar drone parrot reservedeleDrone 1.0) - You can also use a LLC (logic level converter), but since my AR.ar drone 2 dosahDrone is the older 1.0, a resistor was good enough - 2mm headers for AR.parrot ar drone manette ps3/ProductDetail/Harwin/M22-71...AR.Drone 2.0+- LLC (logic level converter), You have to have this or you'll FRY the Drone 2.0+ http://mirumod.tk//hw/mirullc/mirullc.php - See schematics on how to wire it http://mirumod.tk/hw/arduino_pro_mini/arduino_pro...- 2mm male headers for AR Drone 2.0 - http://mirumod.tk/hw/arduino_pro_mini/arduino_pro...Radio system I'm using a Spektrum DX6i transmitter (TX) and AR6100e receiver (RX), but will probably switch to my Turnigy 9X. parrot ar drone unknown emergency

You can use any programmable radio system as long as it has 5 or more channels. FrSky Taranis, Walkera Devo 7e/10, Spektrum DX6/7/8/9, and many others. microdrones md4-1000 youtubeJust make sure you test it throughly with the serial monitor to ensure all the controls are working right before doing a test flight. drone md4-1000 priceAlternative radio system (Spektrum compatible): - OrangeRX T-SIX transmitter - http://bit.ly/hkorxtsix - OrangeRX DSM2/DSMX receiver - http://bit.ly/hkorxtsix Documentation and schematics: http://mirumod.tk/hw/arduino_pro_mini/arduino_pro...Software: mirumod 022 by miru - http://mirumod.tk Arduino IDE - http://mirumod.tk HyperTerminal - http://mirumod.tk 3D printed bottom plastic cover plate Thingiverse. /thing:1132554This is a very involved project with lots of components and issues that can pop up so take your time.

You'll be a better person after it's all done :)If you can't be bothered with all this nonsense, you can buy it from miru himself! I It's a tiny all-in-one board with the drone connector, USB, and LLC (Logic Level converter) that you just plug into your Drone and configure your transmitter. by KenVersus is licensed under the Creative Commons - Attribution license. If you print this Thing and display it in public proudly give attribution by printing and displaying this tag. This is a custom part for my Parrot AR Drone 1.0 that was converted to work with an RC transmitter like the Spektrum DX6i. I had to create a custom bottom plate so there would be room for the cable. I thought this might be useful for someone out there. You can print one if you lost your original cover plate or maybe you're modding the AR.I'm not sure if it'll work with the newer 2.0 AR. You might have to expand the holes a bit with a drill bit. By downloading this thing, you agree to abide by the license:

Upgrade this Thing with Thingiverse Apps Edit, personalize, or revise this Thing Order a print of this Thing Repair, slice, or enhance this Thing 3D Print your file with 3D Hubs, the world’s largest online marketplace for 3D printing services. 3D Print with 3D Hubs Auto-magically prepare your 3D models for 3D printing. A cloud based 3D models Preparing and Healing solution for 3D Printing, MakePrintable provides features for model repairing, wall thickness... Kiri:Moto is an integrated cloud-based slicer and tool-path generator for 3D Printing, CAM / CNC and Laser cutting. 3D printing mode provides model slicing and GCode output using built-in... With 3D Slash, you can edit 3d models like a stonecutter. A unique interface: as fun as a building game! The perfect tool for non-designers and children to create in 3D. Print through a distributed network of 3D printing enthusiasts from across the US, at a fraction of the cost of the competitors.

We want to change the world for the better through technology, an... 3D Print with Print a Thing As I mentioned earlier, we’ve got an AR Drone to play with. One of the common mods that popped up on the internet were ways of extending the range on the AR Drone. It normally uses a local Wi-Fi connection to your phone or tablet for control and video signals. Many found this quite restrictive and have gone pretty far in extending that range. The first and easiest was just to set up a higher power Wi-Fi Bridge where you’ll be flying. The Drone only has about 15db of wi-fi magic in it, so anything stronger than that is an improvement. There were too many variations on this to delve into the details, but as you see, there’s not much too it. The second method is to completely replace the Wi-Fi control system with a nice R/C controller. This will greatly increase your range as well as give you extra channels for triggering different attachments (usually lights).  I’ve seen two main methods used.