In order to exit Valet Mode follow the steps listed below: ALL 4 BUTTON REMOTES: Press and release the lock button and the trunk button simultaneously (buttons I & III). Holding the buttons for over .5 seconds will cause this to fail. You will receive two parking light flashes to inform you that this was successful. If you receive 3 parking light flashes followed by 10 parking light flashes upon the remote start command: Simply turn the key to the ‘on’ position and press the foot brake down 10 times within 10 seconds. If you do not receive these flashes: Attempt to reprogram the remote to the vehicle. Cycle the vehicle key between the 'off' and 'on' positions in the ignition 5 times within 7 seconds. Immediately press and release the lock button on the compustar remote (button I). Tap the function or 'F' key on the side 3 times, then press the lock button. Press and release the function button and the trunk button simultaneously.

NOTE: You must be within range of the vehicle, the vehicle must be turned off, the doors must be closed, and you must have battery power in both the remote and vehicle. If you do not have a remote, then the following can be attempted: Press and release the foot brake pedal 10 times within 10 seconds. This procedure will only deactivate Valet Mode it will not activate Valet Mode. The vehicles parking lights should flash 2 times to indicate the system has exited valet mode Troubleshooting: If you are unable to exit valet mode with the instructions listed above, try the following steps. Attempt to reprogram the remote. Replace the battery in the remote. Check to see if the remote is in a button hold mode (remote will beep at you and say hold on the LCD screen) Visit your local dealer or original installer of the product for assistance.Share your review of the Bebop Drone and rate it online: Are you a Bebop Drone pilot? Tell us about your experience in 3 simple steps:

1. Rate your Bebop Drone on your favourite webstore 2. Paste the link of your review into the comment section below this article 3. Get a chance to win a Bebop Charger! * As per the Competition & Consumer Act policy, remember to mention that you are taking part in this marketing operation when sharing your product reviews. ← Zik 2.0 – Your opinion matters to usparrot ar drone legislation Dr. Garza with his vegetable harvest — thanks to Parrot Flower Power! parrot ar drone illegal The DJI Intelligent Flight Battery has a capacity of 5350 mAh, a voltage of 15.2V, and a smart charge/discharge functionality. ar drone 2 fliegenIt should only be charged using an appropriate charger that has been approved by DJI.macdev drone dx release date

DJI Intelligent Flight Battery Functions: 1. Battery Level Display: The LED indicators display the current battery level. 2. Battery Life Display: The LEDs display the current battery power cycle. 3. Auto-Discharging Function: To prevent swelling, the battery automatically discharges to below 65% of total power when it is idle for more than ten days. ar drone parrot kaufenIt takes around two days to discharge the battery to 65%. parrot ar drone htc desireIt is normal to feel moderate heat being emitted from the battery during the discharge process. Discharge thresholds can be set in the DJI GO app. 4. Balanced Charging: Automatically balances the voltage of each battery cell when charging. 5. Overcharge Protection: Charging automatically stops when the battery is fully charged. 6. Temperature Detection: The battery will only charge when the temperature is between 5°C (41°F) and 40°C (104°F).

7. Over Current Protection: The battery stops charging when high amperage (more than 8 A) is detected. 8. Over Discharge Protection: To prevent over-discharge damage, discharging automatically stops when the battery voltage reaches 12 V. 9. Short Circuit Protection: Automatically cuts the power supply when a short circuit is detected. 10. Battery Cell Damage Protection: The DJI GO app displays a warning message when a damaged battery cell is detected. 11. Battery Error History: Browse the battery error history in the DJI GO app. 12. Sleep Mode: To save power, the battery enters sleep mode after 20 minutes of inactivity. 13. Communication: Information pertaining to the battery’s voltage, capacity, current, etc. is transmitted to the aircraft’s main controller. Refer to Phantom 4 Intelligent Flight Battery Safety Guidelines before use. Users take full responsibility for all operations and usage. 1. Battery capacity is significantly reduced when flying in low temperature (< 0°C) environments.

2. It is not recommended that the battery be used in extremely low temperature (< -10°C) environments. Battery voltage should reach the appropriate level when operating environment with temperatures between -10°C and 5°C. 3. End the flight as soon as the DJI GO app displays the “Low Battery Level Warning” in low temperature environments. 4. Keep the battery indoors to warm it before flying in low temperature environments. 5. To ensure optimal performance of the battery, keep the battery temperature above 20°C. 6. The charger will stop charging the battery if the battery cell’s temperature is not within the operating range (0°C ~ 40°C ). In cold environments, insert the battery into the battery compartment and allow the aircraft for approximately 1-2 minutes to warm up before taking off. The Battery Level Indicators display how much power remains. When the battery is turned off, press the Power Button once. The Battery Level Indicators will light up to display the current battery level.

See below for details. Battery life refers to how many more times the battery can be discharged and recharged before it must be replaced. When the battery is turned off, press and hold the Power Button for 5 seconds to check the battery life. The Battery Level Indicators will light up and/or blink for two seconds, as shown below: Charging the Intelligent Flight Battery 1. Connect the Battery Charger to a power source (100-240 V 50/60 Hz). 2. Connect one end of the charger to the Intelligent Flight Battery to the Battery Charger. If the battery level is above 95%, turn on the battery before charging. 3. The Battery Level Indicator will display the current battery level as it is charging. 4. The Intelligent Flight Battery is fully charged when the Battery Level Indicators are all off. 5. Air-cool the Intelligent Flight Battery after each flight. Allow its temperature to drop to room temperature before storing it for an extended period. The table below shows battery protection mechanisms and corresponding LED patterns.